30
menù impostazione - regolazione - diagnostica
2 IMPOSTAZIONE PARAMETRI CALDAIA
2 1 INSERIMENTO CODICE D’ACCESSO 222
premere il tasto programmazione
per selezionare 234 e premere
il tasto MENU/OK
2 2 IMPOSTAZIONI GENERALI CALDAIA
220Lenta Accensione da 0 a 99
Vedi tabella regolazione gas
221Temperatura antigelo Zone da 2 a 10(°) 5
Il parametro è visualizzato solo con connessione a dispositivi
modulanti (optional)
222NON ATTIVO
223NON ATTIVO
224NON ATTIVO
225Ritardo partenza in
riscaldamento
0= Disattivato
1= 10 secondi
2= 90 secondi
3= 210 secondi
0
Utilizzare con Clip-in 2 zone (optional)
226NON ATTIVO
227NON ATTIVO
228Versione Caldaia
NON MODIFICARE
da 0 a 5 0
RISERVATO AL SAT Solo in caso di sostituzione della scheda
elettronica
2 3 PARAMETRI RISCALDAMENTO - PARTE 1
230Massima potenza
riscaldamento Assoluta
da 0 a 99
RISERVATO AL SAT Solo in caso di sostituzione della scheda
elettronica o cambio gas - vedi paragrafo Regolazione Gas
231Max Potenza
Riscaldamento regolabile
da 0 a 99 60
vedi paragrafo Regolazione Gas
232NON ATTIVO
233NON ATTIVO
234NON ATTIVO
235Selezione Tipologia
ritardo d'accensione in
riscaldamento
0 = Manuale
1 = Automatico
1
236Impostazione tempo
ritardo d'accensione in
riscaldamento
da 0 a 7 minuti 3
237Post-circolazione
riscaldamento
da 0 a 15 minuti o CO
(in continuo)
3
238Tipologia di funzionamento
del circolatore
0 = Bassa Velocità
1 = Alta Velocità
2 = Modulante
2
239Impostazione del Delta T
Modulazione Circolatore
da 10 a 30 °C 20
Da impostare con funzionamento del circoltore in modalità
modulante
Tale parametro permette di impostare la di erenza di
temperatura tra mandata e ritorno che determina la
commutazione tra bassa ed alta velocità del circolatore
Es: param. 239 = 20 se la Tman - Trit > di 20 °C il circolatore
viene attivato alla massima velocità. Se Tman - Trit < di 20 -
2°C il circolatore viene attivato alla minima velocità.
Il tempo di attesa minimo tra il cambio di velocità è di 5
minuti.
2 4 PARAMETRI RISCALDAMENTO - PARTE 2
240NON ATTIVO
241NON ATTIVO
242NON ATTIVO
243Post-ventilazione dopo
richiesta riscaldamento
0 = OFF (5 secondi)
1 = ON (3 minuti)
0
menu
sotto-menu
parametro
descrizione range
impostazioni di
fabbrica
note
2 BOILER PARAMETER
2 1 SERVICE CODE 222
press the programming
button to select 234 and press the
MENU button
2 2 BOILER GENERAL SETTINGS
220Soft ignition from 0 to 90
see parag. Gas settings
221Zone Frost Temperature
(Room Temperature)
from 2 to 10 (°C) 5
only active when the BUS device is connected
222Fun Modulation On/O 0 = modulation
disabled
1 = modulation active
1
223NOT ACTIVE
224NOT ACTIVE
225Heating ignition delay 0 = Deactivated
1 = 10 seconds
2 = 90 seconds
3 = 210 seconds
0
Utilizzare con Clip-in 2 zone (optional)
226NOT ACTIVE
227NOT ACTIVE
228Boiler version
- NOT TO MODIFY
from 0 to 5 0
ONLY FOR SERVICE - To be used only in substitution P.C.B.
2 3 CENTRAL HEATING PARAMETER PART 1
230Maximum Central Heating
Aboslute power
from 0 to 99
ONLY FOR SERVICE - To be used only in
substitution P.C.B. see parag. Gas settings
231Maximum Central Heating
power Adjustable heating
from 0 to 99 60
see parag. Gas settings
232NOT ACTIVE
233NOT ACTIVE
234NOT ACTIVE
235Anti-cycling time mode 0 = Manual
1 = Automatic
1
236Anti-cycling time (If 235 = 0) from 0 to 7 (minutes) 3
237Central Heating pump
overrun
from 0 to 15 (minu-
tes) o CO (continuos)
3
238Pump speed control 0 = Low speed
1 = High speed
2 = Modulating
2
239Set Delta T Pump from 10 to 30 (°C) 20
Parameter to set if Pump Speed control (237) is setted on
modulating
ΔT ( ow - return) for circulation pump modulation
This parameter can be used to set the di erence between
the ow and return temperatures, which determines the
commutation between low and high circulation pump
speed. E.g.: param. 14 = 20 if the T ow - Tret > 20°C; the
circulation pump will be activated at maximum speed. If the
T ow - Tret < 20 - 2°C; the circulation pump will be activated
at minimum speed.
The minimum wait time between speed changes is 5
minutes.
2 4 CENTRAL HEATING PARAMETER PART 1
240NOT ACTIVE
241NOT ACTIVE
242NOT ACTIVE
243Post-ventilation after Central
Heating request
0 = OFF
1 = ON
0
menu
sub-menu
parameter
description value
default
setings
notes
Commentaires sur ces manuels